ip route cache command

  1. Cisco IOS Switching Services Command Reference, Release 12.3 ...
    The ip route-cache command with no additional keywords enables fast switching. ... To reenable CEF or dCEF operation, use the ip route-cache cef command. ...

  2. Cisco IOS Release 12.0 Switching Services Command Reference ...
    To configure IP multicast fast switching or multicast distributed switching (MDS), use the ip mroute-cache interface configuration command. ...

  3. IBM/Cisco Interoperability
    The 'ip mroute-cache' command enables fast switching of multicast packets ... The 'no ip mroute-cache' command turns it off and all multicast packets on the ...

  4. ip route-cache and CEF
    be fast switched, use the no ip route-cache command on the egress interface to disable fast switching. -- Joe Drago StreamLine Communications ...

  5. O'Reilly - Safari Books Online - 9780596101510 - Network Warrior
    On an interface that is currently process switching, the interface command ip route-cache enables fast switching: R1(config)# int s0/1 R1(config-if)# ip ...

  6. O'Reilly - Safari Books Online - 1578701570 - Cisco IOS 12.0 ...
    To enable CEF operation on an interface after CEF operation has been disabled, use the ip route-cache cef interface configuration command. ...

  7. Adobe Press - 1578701570 - Cisco IOS 12.0 Switching Services
    Cisco IOS Switching Commands > ip route-cache ... Use the ip route-cache interface configuration command to control the use of high-speed switching caches ...

  8. Adobe Press - 1578701570 - Cisco IOS 12.0 Switching Services
    ip route-cache flow. To enable NetFlow switching for IP routing, use the ip route-cache flow interface configuration command. To disable NetFlow switching, ...

  9. Caligare / Knowledgebase / What is difference between "ip flow ...
    If you configure the ip flow ingress command on a few selected subinterfaces and then configure the ip route-cache flow command on the main interface, ...

  10. AdventNet Discussions :: ip route-cache flow
    The "ip route-cache flow" command has to be executed on each interface for which you want to see incoming/outgoing traffic. ...

  11. Re: Possible DoS attack (?)
    To disable the sending of redirect messages, use the no form of this command. ip route-cache To control the use of a high-speed switching cache for IP ...

  12. Caligare / Knowledgebase / I have interface Vlan2 with record ip ...
    Try the command "show ip interface brief" to display brief summary of IP status ... What is difference between "ip flow ingress" and "ip route-cache flow"? ...

  13. AdventNet Discussions :: ip route-cache flow ..... why
    You do need to run the " ip route-cache flow" command in order to export netflow data. "ip route-cache CEF" is used only to enable Cisco Express Forwarding ...

  14. NeTAMS - documentation
    ip cef ! ip flow-cache timeout inactive 60 ip flow-cache timeout active 10 ! interface FastEthernet0/0 ip address 192.168.1.1 255.255.255.0 ip route-cache ...

  15. JLSNet :: Cisco Configs : Connecting through a Dialup Modem
    The recommended action is to use the "no ip route-cache" command to disable fast switching on whatever configuration source provides the configuration for ...

  16. Cisco IOS DFS Access List Leakage Vulnerabilities
    If the command ip route-cache distributed does not appear in your router configuration file, then you are not affected by either vulnerability. ...

  17. Documentation
    interface Loopback0 ip address 192.168.10.1 255.255.255.0 ip route-cache ... as the subscriber receives data from the Internet run a command at the router: ...

  18. CONFIGURING A CISCO ROUTER, PART 1 THE JOB OF THE ROUTER In the ...
    These are routes that you insert with the "ip route" command. .... Hssi 1 0 ip route 137.239.0.0 255.255.0.0 Hssi 1 0 252 ip route-cache cbus ip route-cache ...

  19. Should I enable ip-route cache flow on Loopback0?
    To: <cuflow-users@columbia.edu>; Subject: Should I enable ip-route cache ... no ip proxy-arp ip route-cache flow ! rest of the relevant netflow commands in ...

  20. ip route-cache and load balancing
    route-cache is only used for packets being forwarded. Also, if you have CEF enabled on the router, its "ip load-sharing per-packet" command may take ...

  21. [LARTC] Ip route cache problem
    [LARTC] Ip route cache problem. Ionut Popovici ionut at topall.ro ... the iptables nat command >worked, but it seems a random effect and not always works. ...

  22. Voice, IP, and ATM MPLS Features > Commands for Configuring the RPM
    Many of the commands for the RPM require that you be in privileged EXEC mode. ... interface Ethernet2/1 no ip address no ip route-cache no ip mroute-cache ...

  23. D.2. ip route
    If you do use the ip route change command, you should be aware that it does not communicate a routing table state change to the routing cache, ...

  24. ip-cref
    ip mroute -- multicast routing cache management · Abbreviations: · Object: · Commands: · ip mroute show -- list mroute cache entries ...

  25. Linux-Net Archive: why does "ip route flush cache" ta
    "route -C" running in one window with a timestamp (seconds and microseconds) after each iteration. I then issue the "ip route flush cache" command with a ...

  26. Load Balancing with Multiple T1s and cisco Routers.
    As it is configured above, cisco routers will default to fast switching. A route cache will be created. You can check it with the "show ip cache" command. ...

  27. - no ip mroute-cache, help plz!
    So I have been researching ip mroute-cache theres alot of docs and I have .... I seem to remember even though it had a full duplex command it did not work. ...

  28. Cisco IOS
    where "ip addr" is the IOS command, and the next 6 values are the options. ... no ip directed-broadcast ip nat outside no ip route-cache no ip mroute-cache ...

  29. Setting up Cisco NetFlow :: User Guide
    show ip cache flow, These commands summarize the active flows and give an ... router-2621(config-if)#ip route-cache flow router-2621(config-if)#exit ...

Related information "ip route cache command":

Home Sitemap