ip route command

  1. Static Route Commands
    When network is A.B.C.D format, user must define netmask value with A.B.C.D format. gateway is same option as above command ip route 10.0.0.0 255.255.255.0 ...

  2. ip route
    Use the ip route route-prefix mask gateway syntax to configure a static path to the specified destination via the specified gateway. This command can be ...

  3. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols ...
    Use the ip policy route-map command, in addition to the route-map command, ... Command. Description. ip policy route-map. Identifies a route map to use for ...

  4. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols ...
    The ip local policy route-map command identifies a route map to use for local policy .... To establish static routes, use the ip route command in global ...

  5. Static Routing
    CISCO 'ip route' command: ip route 0.0.0.0 0.0.0.0 <next hop|exit interface> ... CISCO 'null route' command: ip route 202.148.224.0 255.255.255.128 e0 ip ...

  6. Add a static IP route
    Specifies either an IP address or host name for the network or host. ... If a route addition fails, you can use the tracert command to verify that the ...

  7. TCPmag.com | Q and A: Using the Track IP Route Command
    TCPmag.com Salary Survey: Using the Track IP Route Command.

  8. D.2. ip route
    All operations with the ip route command are atomic, so each command will .... The command ip route show table special shows us routing table number 7 from ...

  9. Cisco::ShowIPRoute::Parser - parse Cisco 'show ip route' command ...
    This File contains the encapsulation of Raj's route parser. It will parse the output from a Cisco 'show ip route' command and return all the routes to a ...

  10. Linux-Net Archive: `nexthop` at "ip route" command.
    Next in thread: Fabian Gervan: "Re: `nexthop` at "ip route" command. ... 'nexthop' parameter at the 'ip route' command to do the correct output ...

  11. Linux-Net Archive: Re: `nexthop` at "ip route" comman
    'nexthop' parameter at the 'ip route' command to do the correct output ... you can try the "ip route" and "nexthop". But therefore the command line ...

  12. O'Reilly - Safari Books Online - 0596008694 - Cisco IOS in a ...
    To create a default network, use the ip default-network command. This route is usually created in tandem with the 0.0.0.0 0.0.0.0 route for completeness, ...

  13. O'Reilly - Safari Books Online - 9780596101510 - Network Warrior
    The IP Routing Table. To show the IP routing table, use the show ip route command:. Code View: Scroll / Show All. R2# sho ip route Codes: C - connected, ...

  14. ip-cref
    IP Command Reference. Alexey N. Kuznetsov Institute for Nuclear Research, Moscow ... ip route replace -- change a route or add a new one ...

  15. Cisco CCNA Certification Exam Distance Vector Static Routing
    Topics include IP route, connected routes, turning debugs off and on, troubleshooting, router rip command, subnet masks, serial interfaces.

  16. COTSE - ADDTCPRTE (Add TCP/IP Route) Command
    The Add TCP/IP Route (ADDTCPRTE) command is used to identify a route to a remote network or a route to a remote destination system in the Transmission ...

  17. IP Command Reference. Contents
    File Format: Adobe PostScript - View as Text
    route. Recall that Linux-2.2 supports multiple tables managed with the ip route. command, described in the previous section. ...

  18. Microsoft Windows XP - Route
    -p : When used with the add command, the specified route is added to the registry and is used to initialize the IP routing table whenever the TCP/IP ...

  19. Configure static routes in Debian or Red Hat Linux systems
    By using the ip command, you can setup static route. ... You can add static route using following command: ip route add {NETWORK} via {IP} dev {DEVICE} ...

  20. iproute2+tc notes
    ip command. ip link; ip address; ip neighbor; ip rule; ip route; ip tunnel; ip maddress; ip mroute; ip monitor. rtmon command; tc command ...

  21. Static Routes in the Cisco IOS
    You can also see our connected interfaces (shown with a C). As a side-note, the show ip route command can be abbreviated sh ip ro. ...

  22. RMVTCPRTE Command Description
    The Remove TCP/IP Route (RMVTCPRTE) command removes a previously identified route from the Transmission Control Protocol/Internet Protocol (TCP/IP) ...

  23. TRCTCPRTE Command Description
    The Trace TCP/IP Route (TRCTCPRTE) command, also known as TRACEROUTE, traces the route of IP packets to a user-specified destination system. ...

  24. Linux Route Hacks
    for a system with two IP addresses. Note the multiple default routes, although the route command does not provide information to distinguish much, ...

  25. Configuring static and default routing
    To configure a static route, use the global configuration command ip route. ... ip route: The command used to add a static or default route ...

  26. Troubleshoot Windows TCP/IP problems with our Route Utility
    When you're troubleshooting TCP/IP connectivity problems on a Windows ... For example, Windows 98's Route command line tool doesn't provide the -p or the If ...

  27. CISCO BGP Commands
    The no command is used *before* any other configuration-mode command - it's the way that you tell a Cisco to unset a setting. For example, no ip route ...

Related information "ip route command":

Home Sitemap