ip route commands

  1. Static Route Commands
    When network is A.B.C.D format, user must define netmask value with A.B.C.D format. gateway is same option as above command ip route 10.0.0.0 255.255.255.0 ...

  2. ip route
    The ip route commands define an ECMP set of 4 static routes with the same destination address and netmask, but 4 different gateway addresses. ...

  3. Microsoft TechNet: Understanding the IP Routing Table: The Cable ...
    To view the IP routing table on a computer running Windows XP or Windows Server 2003, type route print or netstat -r at a command prompt. ...

  4. IP Command Reference. Contents
    File Format: Adobe PostScript - View as Text
    route. Recall that Linux-2.2 supports multiple tables managed with the ip route. command, described in the previous section. ...

  5. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols ...
    Another purpose of route maps is to enable policy routing. Use the ip policy route-map command, in addition to the route-map command, and the match and set ...

  6. Cisco IOS IP Command Reference, Volume 2 of 3: Routing Protocols ...
    The no ip local policy route-map command deletes the reference to the ... The ip policy route-map command identifies a route map to use for policy routing. ...

  7. Static Routing
    CISCO 'null route' command: ip route 202.148.224.0 255.255.255.128 e0 ip route ... CISCO router commands: SPECIFIC ROUTES (used unless down) ip route ...

  8. IP Routing
    For small LANs, it is usually most efficient to construct them by hand and feed them to IP using the route command at boot time (see Chapter 5). ...

  9. Add a static IP route
    Specifies either an IP address or host name for the network or host. ... If a route addition fails, you can use the tracert command to verify that the ...

  10. Routing in the Internet
    An IP address of 0.0.0.0 is regarded as a default address. Routers will receive RIP information and will use it to determine their shortest route to a ...

  11. TCPmag.com | Q and A: Using the Track IP Route Command
    TCPmag.com Salary Survey: Using the Track IP Route Command.

  12. D.2. ip route
    All operations with the ip route command are atomic, so each command will .... The command ip route show table special shows us routing table number 7 from ...

  13. Advanced routing mini-HOWTO
    All this is done automatically, you should not type no command now. To check up what do we have in table N just type ip route list table N . ...

  14. Configure Local IP Routing Table
    If you want to manually specify the optimal route for IP packets, ... use the route command to display, add, and edit the local route tables for your ...

  15. Linux-Net Archive: `nexthop` at "ip route" command.
    I think that I can use the 'ip rule' and 'ip route' commands. As the ... 'nexthop' parameter at the 'ip route' command to do the correct output ...

  16. Linux-Net Archive: Re: `nexthop` at "ip route" comman
    'nexthop' parameter at the 'ip route' command to do the correct output ... you can try the "ip route" and "nexthop". But therefore the command line ...

  17. O'Reilly - Safari Books Online - 0596008694 - Cisco IOS in a ...
    To create a default network, use the ip default-network command. This route is usually created in tandem with the 0.0.0.0 0.0.0.0 route for completeness, ...

  18. IP Route Provider (Windows)
    ... IP Route provider supplies IPV4 network routing information, including (but not limited to) the information available through the route print command. ...

  19. Linux Route Hacks
    for a system with two IP addresses. Note the multiple default routes, although the route command does not provide information to distinguish much, ...

  20. Cisco::ShowIPRoute::Parser - parse Cisco 'show ip route' command ...
    This File contains the encapsulation of Raj's route parser. It will parse the output from a Cisco 'show ip route' command and return all the routes to a ...

  21. TCP/IP Routing Basics for Windows NT
    In the TCP/IP configuration, you can add a default route for each network card. ... TITLE : "P" Switch for Route Command Added in Windows NT ...

  22. ip-cref
    IP Command Reference. Alexey N. Kuznetsov Institute for Nuclear Research, Moscow ... ip route replace -- change a route or add a new one ...

  23. show ip route
    Command Mode: Executive and privileged. Example 1: In the following example, the show ip route command with no arguments displays all routes: ...

  24. CCNP Certification Training BSCI Static IP Route Commands
    Cisco CCNP certification training article for BSCI exam candidates, dealing with different administrative distances for static routes. Proper use of ip ...

  25. COTSE - ADDTCPRTE (Add TCP/IP Route) Command
    The Add TCP/IP Route (ADDTCPRTE) command is used to identify a route to a remote network or a route to a remote destination system in the Transmission ...

  26. O'Reilly - Safari Books Online - 9780596101510 - Network Warrior
    The IP Routing Table. To show the IP routing table, use the show ip route command:. Code View: Scroll / Show All. R2# sho ip route Codes: C - connected, ...

  27. [rancid] Re: Monitoring Route Table with RANCID.
    Made this addition which I'd like to share because I spent some time in trial & error with escaping the "*" in "show ip route vrf * bgp", ...

  28. [rancid] Re: Monitoring Route Table with RANCID.
    Previous message: [rancid] Re: Monitoring Route Table with RANCID. .... + "show ip route static", > + "show ip route rip", > + "show ip route igrp", ...

  29. route(8): show/change IP routing table - Linux man page
    Route manipulates the kernel's IP routing tables. Its primary use is to set up static routes to specific hosts or networks via an interface after it has ...

Related information "ip route commands":

Home Sitemap